- Jukebox-list - lists.netlojix.com

LPC 480 mech
by Tony Miklos 14 Jun '24

14 Jun '24

I think I've seen this problem once before but don't know what model seeburg it was. Anyway I have the LPC ready to be picked up and after several hundred test plays, the mech decides to jamb up. The motor will be on and trying to turn but no go. Turn off the motor and it sort of backs up a hair away from the side it was trying to go. For the life of me I just don't see what it is. There is a little play in there and if I toggle the reversing switch back and forth it will scan 4 or 5 spaces then jamb, flip the switch and it goes the other way. I'm pulling my hair out and I don't have much left! It isn't anything mechanical from the mech to the cabinet, when it's stuck all areas of the mech can still be wiggled around. Nothing at all like the cable getting stuck, that's for sure. I'm thinking something with the bell crank for the tone arm, but the tone arm does move left and right. Once again, I can't find my books from Ron Rich in case he has any tips for that in there. Tony

3 7

Trashcan
by Jukebox Repairman 08 Jun '24

08 Jun '24

I’m looking for an oiling diagram for a Trashcan. Does anyone have a page to scan / share? Thanks Rick

2 1

Seeburg 100W Pilasters
by Tony Miklos 06 Jun '24

06 Jun '24

I have a customer that has a W with 100C looking pilasters (light snowflake) and color cylinders. He is thinking of going original but wants to know how much he can (or I can) get for his old stuff. They will fit into a 100G but will they fit in anything else? Any ideas what they would be worth? How about to someone here? :) :) :) The color cylinders have good color and the motors are both working.

2 1

Further help with KH200
by morganfield1913＠gmail.com 05 Jun '24

05 Jun '24

Hello, I have a Seeburg KD200H which has been working for 10 years. However, now after making a selection it now plays all records sequentially starting at the position where the mechanism rested ignoring the selection. I have conducted the following: 1. Measured the Play Control 'Sub' and 'Add' solenoids - both 12Ω, 26mH 2. Replaced 12AX7 3. Replaced 56k Ω resistor in TEU 4. Checked TEU1 voyage -300VDC 5. Checked the Tormat return path 190 Ω 6. Cleaned the following: a. Play Control contacts b. Detent switch c. Tormat readout RCA connector d. All relay contacts on the Mechanism All did not fix the problem. I will appreciate your help. Thanks Rod.

1 0

SHFA1, 2, 4.. Mute/Squelch plug 5 pin
by Tony Miklos 31 May '24

31 May '24

Anyone have a mute/squelch 5 pin plug for sale? I may have a plug you need for trade. Tony

2 4

W61 Continued issue
by M De Simone 28 May '24

28 May '24

Still working on the model 61. With the help of Hans I was able to replace the fibre gear, it went together well and works fine. (Thank you Hans) The problem now is that it keeps picking up the same record and the selector never searches. The problem is that at the end of the cycle the clutch does not reset forward and engage the selector gear. However if I advance the mech a bit it will do what it’s supposed to do. I’ve done the timing at least 5 times but it hasn’t corrected the problem, I’ve even tried advancing the timing a bit and retarding it a bit and still no luck so I just set the gear back to where it’s supposed to be. Is there an adjustment to make the motor run a bit longer? I’ve read the manual cover to cover but no mention of this. In the troubleshooting section it says to do the timing, but as I stated, this did not solve the issue. Any ideas much appreciated. Mauro Sent from my iPhone

2 2

Seeburg KD200 Plays Continously
by Glenis&Rod 23 May '24

23 May '24

Hello, I have a Seeburg KD200 which has been working for 10 years. However, now after making a selection it now plays all records sequentially starting at the position of the mechanism ignoring the selection. I have a Service Manual which describes in detail settling and adjustments. In order to trace this fault a 'Control Sequence Diagram' would be very useful. I have seen Control Sequence Diagrams for later Seeburg JBs - semiconductor models which gives some information. I have inquired on other forums without reply. Any diagnostic information will be appreciated. Can anyone please tell me "what is the signal or relay/solenoid that is activated when a record has been returned to the rack"? Rod

2 1

Turntable fibre gear replacement
by M De Simone 22 May '24

22 May '24

I’ve noticed a few people replacing the main fibre gear on W61 countertop jukeboxes, I have mine apart and need to replace the turntable fibre gear. I have the assembly out of the mech and on the bench but can’t figure out how to get the shaft out of the cast metal assembly that holds the worm gear. Can it just be done as is or does this shaft have to be removed? Any insight much appreciated as I’d like to get this back together and out of my work space! Thanks, Mauro Mississauga, Ontario, Canada Sent from my iPhone

3 2

Seeburg KD200 plays continuously
by morganfield1913＠gmail.com 21 May '24

21 May '24

Hello, I have a Seeburg KD200 which has been working for 10 years. However, now after making a selection it now plays all records sequentially starting at the position of the mechanism ignoring the selection. I have a Service Manual which describes in detail settling and adjustments. In order to trace this fault a 'Control Sequence Diagram' would be very useful. I have seen Control Sequence Diagrams for later Seeburg JBs - semiconductor models which gives some information. I have inquired on other forums without reply. Any diagnostic information will be appreciated. Can anyone please tell me "what is the signal or relay/solenoid that is activated when a record has been returned to the rack"? Rod

2 1

Rowe R-81 Memory Unit
by Tony Miklos 19 May '24

19 May '24

Is there any hope for finding a known good replacement memory unit #601-07666? I don't recall the condition of the bad board, last I saw it was 10? years ago and I couldn't find a replacement then.

3 4

2026

2025

2024

2023

Jukebox-list