September 2023 - Jukebox-list - lists.netlojix.com

Mills dance master amp
by Hans Minderman 10 Apr '26

10 Apr '26

Hi All, I’m finishing up a Mills Dance Master, I have it all mechanically working and I’m now ready to work on the amp (an MCP 1644 amp). I have a schematic for it from the manual but it is not very useful because the caps and resistors are only marked with the mills ‘mcp’ catalog number and not with the actual values. The corresponding parts list has the same issue with just listing the Mills catalog numbers and not actual values. I checked with Bill Bickers at Jukebox friday night but he does not have a schematic with values or a rebuilt kit either. If anyone has a schematic or a listing of the caps and the resistors and choke for this amp please let me know. Thank you for your help. Hans Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows

4 3

Re: [Jukebox-list] AMI Continental 2 Microtecnica bias spring
by Federico Croci 22 Feb '24

22 Feb '24

Thanks!! > Il 17/01/2023 19:51, Chan Gade ha scritto: > Here it is on an arm in the I-200: > https://www.flickr.com/photos/90641375@N06/37325736231/ The hyperlink > probably won't get through, so copy/paste. > > Attached is a shot of the Continental 1 with counterweight. I did this > in 1986. It was necessary to cut off a small section of the mech dress > cap to clear the added counterweight. > > RobNYC -- Federico Croci wiz(a)tilt.it www.tilt.it

8 10

Archives
by JIM & LAURIE DIRKSEN 08 Oct '23

08 Oct '23

I can't seem to find the searchable archives from the list. The link at the bottom of postings doesn't work. It could be operator error, but I like to think it's not. Maybe my phone settings? Anyone else have this problem? Thanks, Jim

4 4

Ok this one is odd
by Jukebox Repairman 01 Oct '23

01 Oct '23

Seeburg AY100, record is in play and when you make any additional selection it causes the mech to trip to scan ?? I’ve never encountered this before. Any ideas?

3 4

New Amp issue. Seeburg MRA1-L6
by Jukebox Repairman 30 Sep '23

30 Sep '23

This amp had been recapped awhile back and working properly. Owner said he went to play, powered on and a very loud hum then blew the fuse. He replaced with same value and same thing happened. Should I be looking for a shorted tube, open resistor?

2 2

Rowe CD 100 transfer motor
by Paul Howlett 28 Sep '23

28 Sep '23

I have a customer that has a CD100 that the transfer motor runs continuously. I have replaced the mech control computer (6108602) and tested the cam switches. If I stop the motor manually at a selected CD it will play the CD. The optical switches are working. The scan/transfer LED is constantly on. The board error LED is on intermittantly. -- Paul Howlett Pinball Paul's 703-361-0420

3 6

Seeburg MRA1-L6 AMP question
by Jukebox Repairman 28 Sep '23

28 Sep '23

I just finished installing a replacement cap kit in the above-mentioned amp. It is being used in a M100C. Using a redhead cartridge (with good needles) I'm finding the output of the amp is poor. Even with the volume maxed the output is nominal. I tested the tubes and the 6V6 drivers only read in the 50 percent range. A couple were 51 -52 but still low. Do you think a fresh set of tubes will increase the output? Regards, Rick

4 5

Seeburg V200 Does not pick up B sides (right side) records
by M De Simone 20 Sep '23

20 Sep '23

Hey All, A jukebox hobby friend asked for my help as he really doesn’t have computer savvy. He has a V200 with a TSR1 selection receiver. When he performs the battery trick all selections are selected and played. Making a selection from the keyboard works fine for all A (left side) selections but the mech will scan twice and not pick up any B side (right side) selections? He has tried swapping the 2D21 tubes and has traced out and verified all the wiring is good with continuity. To me it sounded like a readout problem at first but the fact that it selects and plays all selections when charged by a battery kinda eliminates a readout or trip.problem and the fact that it selects and plays A sides, I think, rules out a write in problem? I was hoping someone could offer some suggestions as I’m really not good at remote troubleshooting and this seems like a very odd problem to me. Much appreciated, Mauro Sent from my iPhone

4 6

NSM Prestige 2 IC 12
by Tony Miklos 18 Sep '23

18 Sep '23

On an NSM Prestige 2 on the board is an IC 12. It's an ER-1400. I think it's a ROM. I found some but do they need to be programmed? Thanks, Tony

1 0

78rpm reproduction records for sale
by joeymcd 12 Sep '23

12 Sep '23

Hey everyone. I have 8 used REPRODUCTION 78rpm records for sale. These would have been from the sets that were sold by Victory Glass and others. I took pictures and there is a list in with the pictures. Anyone interested can email me directly for the pictures and details. Postage by Canada Post. Joey McDonald

2 1