- Jukebox-list - lists.netlojix.com

email change
by Doug Vachon 22 Feb '23

22 Feb '23

Hi, Could you change my email address: Old address: dvachon333(a)cogeco.ca To: dvachon3(a)teksavvy.com Thank you, Doug

1 0

Testing a W1500 amp with newer mech?
by (null) DESIMONE 21 Feb '23

21 Feb '23

Here’s a fun one! I have need to test a Wurlitzer 516 amplifier from a model 1500 but the jukebox is 2 hours away. I have a mech from a 1700 or 1800 set up that I use for testing amplifiers from about models 1800 to 2300. The 516 amplifier uses an 11 pin plug to the amplifier as does say, the 530 amplifier from a model 1900 but when I compare the schematics they appear very different. Would anyone know if I can test this amp with this mech? I do realize the 1500 uses a field coil speaker and I have an adapter for this purpose. I just don’t want to smoke any components and am concerned. Thanks, Mauro Sent from my iPhone

1 0

Mills Do Re Mi
by ascott822 21 Feb '23

21 Feb '23

I have a Mills Do Re Mi that is without a selection drive motor. I have acquired one but need help wiring it in. The motor has four wires (two of course for the AC). Any diagram or drawing directing me where each of these go would be appreciated. Ascott822(a)aol.com. Sent from the all new AOL app for iOS

1 0

Rowe CCC repair 6-08870-06
by Tony Miklos 11 Feb '23

11 Feb '23

I have a darn I forget the model (R-86?), but it has a 6-08870-06 CCC with a very odd problem. After fixing up some battery corrosion, it would power up and play whatever selection it had stopped at, then when that cancels, it proceeds to play both sides of every record. The only way to stop it is to press the "clear selection memory" button. At first I didn't have a battery in it and thought maybe on power up one of the two 5101 rams are getting *confused*. I added a battery and it seemed to have cured the problem. Then yesterday it started doing it again. I do have a small quantity of 5101's in stock. Thanks, Tony

1 0

Re: Wurlitzer 532 hum revisited
by Carl Haines 09 Feb '23

09 Feb '23

Well, I'm done with trying to eliminate this hum for now. I did have some marginal success with reducing it slightly. I was pretty much already done but I came across a few videos on youtube that showed troubleshooting a ground loop hum. I put the amp back on the bench and tried using a piece of wire to make a new ground path from various points. One of these was to place one end of the wire on the ground strap from the ground strap for the PCB to the opposite side of the board near C17. That took some of the edge off the hum but did not eliminate it. I decided to run a 16AWG wire from the strap to the pad for the jumper wire near C17 and leave it that. Maybe some day when I am feeling adventuresome I'll trace out the ground paths to see how many jumpers are used to tie into the perimeter ground plane to see if I can isolate and reground different points on the board. I will note that there is one track for the heater circuit that runs parallel to the ground for quite a bit of distance. The ground strap is at one end of this run and the place where I tied the new wire is at the other end. Other thoughts - I don't know if I am expecting too much here or not. The hum can easily be drowned out with background noise and it is not noticeable when music is playing. I just notice it in the time between when the amp unmutes and the music starts. I'll also admit that my bench testing setup is not the best for testing this due to the small speaker I am using. There is a notable difference between a single 8" speaker and 3 x 12" speakers when it comes to 60hz hum. Carl Haines

5 10

Rowe R-84 Optical Switch
by Tony Miklos 06 Feb '23

06 Feb '23

I can't find a part number for this. Same part for a lot of other models, this one is actually for an RI-3. Anyway can these be bought anywhere? I've seen some used on ebay but sure would like new. I can most likely make one if I really have to but trying here first. I just emailed A&B in NH but they are closed today so I thought I'd look for other leads in the mean time. I believe this is the same part for these jukes: RI-3 / RI-4 / CTI-2 / R-84 to R-94

1 1

Re: Pin Bank Issue
by SFC(r) Rich Myers 06 Feb '23

06 Feb '23

Jamie - Did you ask this question on a FB group too? It sounds familiar. I mentioned the solenoid sticking because the selector button is still making contact. Need to check there first. Don't leave energized or it will burn up. -rm -----Original Message----- From: jukebox-list-bounces(a)lists.netlojix.com [mailto:jukebox-list-bounces@lists.netlojix.com] On Behalf Of Jamie McElroy via Jukebox-list Sent: Saturday, February 4, 2023 6:28 PM To: Jukebox mailing list <jukebox-list(a)lists.netlojix.com> Subject: [Jukebox-list] Pin Bank Issue Hello again, I have an issue with a possibly stuck solenoid on my AMI G-80 pin bank. When I push the cancel button the pin continues to raise back up immediately and won't let the record cancel and scanning to continue. Does anyone have any thoughts on this that would help please? Thank you, Jamie _______________________________________________ Jukebox-list mailing list Jukebox-list(a)lists.netlojix.com http://lists.netlojix.com/mailman/listinfo/jukebox-list Searchable Archives: http://jukebox.markmail.org/ -- This email has been checked for viruses by Avast antivirus software. www.avast.com

1 0

Seeburg TSU5 Selection Issue Solved
by Jerold Kress 05 Feb '23

05 Feb '23

I just learned that the red wire on the Pulse Amp RCA cable needed to be soldered to ground. This has solved the issue! After running the jukebox for a while I notice that R518 is getting warm though the caps on either end of it are not heating up. Something to be concerned about?

1 0

New server test
by Jay Hennigan 05 Feb '23

05 Feb '23

Testing - please ignore. -- Jay Hennigan - jay(a)west.net Network Engineering - CCIE #7880 503 897-8550 - WB6RDV

1 0

Migration test
by Jay Hennigan 05 Feb '23

05 Feb '23

Test, please ignore. -- Jay Hennigan - jay(a)west.net Network Engineering - CCIE #7880 503 897-8550 - WB6RDV

1 0

2025

2024

2023

Jukebox-list