August 2023 - Jukebox-list - lists.netlojix.com

OMT CD slipping
by Tony Miklos 18 Aug '23

18 Aug '23

Working on a Wurlitzer OMT that had a bad CD player. I repaired the CD player and here in the shop when testing it, the turntable would sometimes turn faster than the CD and make some noise. Sometimes it would spin and play, but way too often it ends up putting the CD back and not playing it. I had thought that maybe my Rowe/AMI test juke was somehow different in the clamp arm, with less weight or something? I installed it back into the OMT and it's still spinning/slipping/putting CDs back. The round plastic pressure disc part of the clamp arm is just plastic, no metal and/or magnet. I *think* there was a magnet on the CD player that may have pulled the pressure disc, IF it had any metal in it. To add to the dilemma, the centering cone on the player was missing and I could not find it in the machine. I did install one but am not sure if that has to do with the problem. It doesn't appear to be. So should the pressure disc have a metal washer of sorts in it instead of a magnet?

3 4

Columbus Coin-op Shop ad on eBay
by Andrew Burkhart 11 Aug '23

11 Aug '23

This shop is going out of business. Posting here in case anybody is interested. https://www.ebay.com/itm/126047400225?mkcid=16&mkevt=1&mkrid=711-127632-2357 -0&ssspo=K8NwCQaQTTW&sssrc=2047675&ssuid=&widget_ver=artemis&media=EMAIL I am not affiliated with them in any way. Andrew

4 3

Black Box issue
by Paul Howlett 10 Aug '23

10 Aug '23

I have a Black Box that when selecting any number past 136 it picks up the wrong selection. All the 200's work fine. I replaced the box with another one in the juke and that one worked fine. There used to be a guy in Canada that repaired them and I can't find his info. -- Paul Howlett Pinball Paul's 703-361-0420

5 11

WurliTzer 2900 - 3300 Tonearm Wiring.
by Shankar Singh 07 Aug '23

07 Aug '23

Should these models of tonearms have 4 wires, 1 for each terminal? Or can the 2 (-) close to the cartridge end be connected to each other, so that 3 wires are used in the tonearm? Thank you SHANKAR SINGH

4 4

rockola 1448 Amp question
by Jim McClave 07 Aug '23

07 Aug '23

Hi all , is there supposed to be a power resistor betwwen pins 2 and 5 of the speaker female plug on the amp? Miine has one , the brown sandy kind, thats reading about 12 meg ohms. The schematic just shows a straight wire between 2 and 5 . 2 goes to ground. Thanks, Jim

4 23

Wurlitzer 2410S 1960
by Jon Bellamy 05 Aug '23

05 Aug '23

Hi all, I was hoping for a little advice please. My Wurlitzer 2410S has just stopped working, the selector buttons do not seem to be engaging when pressed. I’ve read the manual and troubleshooting but can’t properly identify the problem/solution. It points to cleaning and adjusting the N. C control contacts as shown on page 12, but I don’t understand the instructions. Can anyone point me in the right direction? Many thanks Jon Sent from my iPad > On 29 Dec 2022, at 21:40, Thomas Lee via Jukebox-list <jukebox-list(a)lists.netlojix.com> wrote: > > The manual show have the specs? > >> On Thu, Dec 29, 2022, 1:38 PM rollin gvtc via Jukebox-list < >> jukebox-list(a)lists.netlojix.com> wrote: >> >> I believe the E80 and the E120 use two belts.motor to idler pulley, and >> idler pulley >> >> to turntable. I think they are the same two belts for the 80 and the 120. >> >> >> >> -- >> This email has been checked for viruses by AVG. >> https://www.avg.com >> _______________________________________________ >> Jukebox-list mailing list >> Jukebox-list(a)lists.netlojix.com >> http://lists.netlojix.com/mailman/listinfo/jukebox-list >> Searchable Archives: http://jukebox.markmail.org/ >> > _______________________________________________ > Jukebox-list mailing list > Jukebox-list(a)lists.netlojix.com > http://lists.netlojix.com/mailman/listinfo/jukebox-list > Searchable Archives: http://jukebox.markmail.org/

2 1

Seeburg SCC3 Code C
by Jukebox Repairman 05 Aug '23

05 Aug '23

I installed new caps in this controller. Now C3109 (lytic) gets hot and will pop if I don’t remove the power. At first I thought I must have polarity reversed but not the case. I have a known good controller that I sat on my bench next to the trouble one and checked each component comparing one by one. Everything matches perfect. The weird part is this SCC was working in the machine before I recapped. I’m at a loss. Has anyone ever experienced this condition before? Regards Rick

3 2

seeburg grey box drd-1
by Jim McClave 04 Aug '23

04 Aug '23

Working on a Seeburg STD4 with the classic scans twice, wont pick a selection problem. Anyone know an easy way to test the grey box? Id be willing to send it off if anyone has a seeburg they could test it in for me. Its the drd-1 type. Jim

2 1

Hello there 🔥
by mario cantin 01 Aug '23

01 Aug '23

mario cantin expects you to verify this - https://529swteh.page.link/ezHe You will be absolutely pleased

1 0

AMI Amplifier?
by Jamie McElroy 31 Jul '23

31 Jul '23

Hello all, I recently rebuilt my AMI G-80 amplifier. I replaced all the capacitors and Ive noticed that I am getting a little humming from my speaker and a little squelchy noise from time to time when my records play. Does anyone have any thoughts? Thanks as always Jamie

7 10