11 Apr
2024
11 Apr
'24
3:13 p.m.
On 2024/04/11 12:17 p.m., Jukebox Repairman wrote:
Well with the aid of the schematic I discovered why the tube heaters and the animation were not working. The connector was dangling in the air. Plugged it in and all works now.
Only downside is now the clamp arm is back to sticking upright after disc loading. When it unloads from the player it goes up high enough to clear the gripper. Nice and smooth motion. I guess I have to remove the mech and get a look underneath
Regards Rick
Does the lift plunger move freely? Could be gummed up lube...
John :-#)#
On Wed, Apr 10, 2024 at 8:49 PM Jukebox Repairman jukin510@gmail.com wrote:
I’m on it. Thanks again On Wed, Apr 10, 2024 at 8:48 PM John Robertson via Jukebox-list <jukebox-list@lists.netlojix.com> wrote: Hi Rick, I was just checking the schematics (#4 OMT & NYNY CD manual - I sell copies) and the NY New York has a small distribution PCB for the bubble tubes and motor. Remove the board and check the backside for burnt or cracked trace(s) - I've seen more than a few fail this way! John :-#)# On 2024/04/10 5:18 p.m., John Robertson via Jukebox-list wrote: > Hi Rick, > > No, if the animation and none of the bubble tubes are running then you > have a power failure. Blown fuse or failure in wiring or connections. > > Check at the motor for the 24VAC needed. You have the schematics I > assume? > > John :-#)# > > On 2024/04/10 5:02 p.m., Jukebox Repairman wrote: >> John am I still looking at defective resistors if all four tubes >> stopped at once? Oddly the animation motor as well >> >> Regards >> Rick >> >> On Wed, Apr 10, 2024 at 6:52 PM John Robertson via Jukebox-list >> <jukebox-list@lists.netlojix.com> wrote: >> >> On 2024/04/09 12:39 p.m., Jukebox Repairman via Jukebox-list wrote: >> > John, thanks. >> > >> > I made the adjustment where the plunger meets the arm. It’s not >> pushing it >> > fully vertical now. It drops back down after disc meets the >> player. >> > As always I appreciate your expertise and help. >> > >> > Now if I can get upper arch bubble tubes to go. >> > I checked fuses all good >> > >> > Regards >> > Rick >> >> Hi Rick, >> >> We carry the correct heater resistors for the bubble tubes used in >> Deutsche Wurlitzers - and we offer free tech advice! >> >> flippers.com <http://flippers.com> <http://flippers.com> >> >> OMT RESISTOR 120 OHM 10% 5 W <#> >> >> Resistors for the bubble tubes, these are held by a >> >> 🔗 https://flippers.com/catalog_oc/resistor-120-ohm-10-5-w-13217 >> <https://flippers.com/catalog_oc/resistor-120-ohm-10-5-w-13217> >> >> Thanks, >> >> John :-#)# >> >> -- John's Jukes Ltd. >> 7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3 >> Call (604)872-5757 (Pinballs, Jukes, Video Games) >> flippers.com <http://flippers.com> <http://flippers.com> >> "Old pinballers never die, they just flip out" >> >> _______________________________________________ >> Jukebox-list mailing list -- jukebox-list@lists.netlojix.com >> To unsubscribe send an email to >> jukebox-list-leave@lists.netlojix.com >> %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s >> Searchable Archives: http://jukebox.markmail.org/ >> > -- John's Jukes Ltd. 7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3 Call (604)872-5757 (Pinballs, Jukes, Video Games) flippers.com <http://flippers.com> "Old pinballers never die, they just flip out" _______________________________________________ Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/
--
John's Jukes Ltd.
7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3
Call (604)872-5757 (Pinballs, Jukes, Video Games)
flippers.com
"Old pinballers never die, they just flip out"