- Jukebox-list - lists.netlojix.com

Seeburg STD 4 Problem
by Jim McClave 15 Oct '23

15 Oct '23

Working on the old "scans Twice doesnt pick up a record " problem. Going by the "symptom 3 troubleshooting guide. The write in voltage at the DCC reads @ 120 Vdc, but I dont see a drop when I make a selection. The guide mentions the write-in trigger. Seems like I dont have that trigger. Anyone else ever experience this ?

1 0

hf100r pupularity meter
by Lore Gianno 15 Oct '23

15 Oct '23

Dear all, today I switched on my hf100r after 3 months of stand by and I have 2 issues (previously it was perfect): I select the song, when then the disc is taken and starts to play the popularity meter solenoid gets activated but it stays activated, thus I have to immediately shut off in order to avoid the solenoid burning. I had a look at the popularity meter block and it seems fine, but for some reasons the solenoid continues to get current... Where does the signal come from? Where should I look? I also noticed a second symptom: pressing the reset switch on the back to stop playing the record does neither work anymore. Any ideas? Thanks Lorenzo

4 8

Re: Archives
by John Robertson 11 Oct '23

11 Oct '23

And unfortunately as far as I can tell the archive.org hasn’t archived the emails as they were stored in a manner it had no access to. My personal archive goes back to January, 2006. Does anyone have an earlier archive? I can see if one of the archives I use can add those messages to a new jukebox list archive… John :-#)# John’s Jukes Ltd. www.flippers.com > On Oct 11, 2023, at 11:32 AM, 19k20(a)comcast.net wrote: > > Sees like they shut it down possibly. > > https://news.ycombinator.com/item?id=37230221 > > -rm > > -----Original Message----- > From: Thomas J. Mertz via Jukebox-list <jukebox-list(a)lists.netlojix.com> > Sent: Sunday, October 8, 2023 12:28 PM > To: Paul Humel via Jukebox-list <jukebox-list(a)lists.netlojix.com>; jrr(a)flippers.com > Cc: Thomas J. Mertz <tjmertz(a)sbcglobal.net> > Subject: [Jukebox-list] Re: Archives > > > At least some of the archive can be found here:Jukebox-list - lists.netlojix.com > > | > | > | | > Jukebox-list - lists.netlojix.com > > > | > > | > > | > > > > > Thomas J. Mertz > tjmertz(a)sbcglobal.net > > > On Sunday, October 8, 2023 at 11:53:37 AM CDT, John Robertson via Jukebox-list <jukebox-list(a)lists.netlojix.com> wrote: > >> On 2023/09/29 7:57 a.m., John Robertson wrote: >>> On 2023/09/29 5:20 a.m., Paul Humel via Jukebox-list wrote: >>> I have the same issue. I get: >>> >>> "This site can't be reached >>> jukebox.markmail.org refused to connect." >>> >>> Paul Humel >> >> web.archive.org didn't capture it either for the past few years... >> >> I have my personal archive that goes back to around 2007 on >> Thunderbird mbox format. >> >> John :-#)# >> >> (I was under pinball(a)telus.net) >> > The domain is paid up to 2025, so the problem must be internal - anyone > know Mark Logic of CA? > > https://www.domain.com/whois/whois/?search=markmail.org > > John :-#(# > >>> >>> -----Original Message----- >>> From: JIM & LAURIE DIRKSEN via Jukebox-list >>> [mailto:jukebox-list@lists.netlojix.com] >>> Sent: Friday, September 29, 2023 2:39 AM >>> To: Jukebox Mailing List >>> Cc: JIM & LAURIE DIRKSEN >>> Subject: [Jukebox-list] Archives >>> >>> I can't seem to find the searchable archives from the list. The link >>> at the >>> bottom of postings doesn't work. It could be operator error, but I >>> like to >>> think it's not. Maybe my phone settings? Anyone else have this problem? >>> Thanks, >>> Jim >>> _______________________________________________ >>> Jukebox-list mailing list -- jukebox-list(a)lists.netlojix.com >>> To unsubscribe send an email to jukebox-list-leave(a)lists.netlojix.com >>> %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s >>> Searchable Archives: http://jukebox.markmail.org/ >>> >>> _______________________________________________ >>> Jukebox-list mailing list -- jukebox-list(a)lists.netlojix.com >>> To unsubscribe send an email to jukebox-list-leave(a)lists.netlojix.com >>> %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s >>> Searchable Archives: http://jukebox.markmail.org/ >> >> > > -- > John's Jukes Ltd. > 7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3 > Call (604)872-5757 (Pinballs, Jukes, Video Games) > flippers.com > "Old pinballers never die, they just flip out" > > _______________________________________________ > Jukebox-list mailing list -- jukebox-list(a)lists.netlojix.com > To unsubscribe send an email to jukebox-list-leave(a)lists.netlojix.com > %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s > Searchable Archives: http://jukebox.markmail.org/ > > _______________________________________________ > Jukebox-list mailing list -- jukebox-list(a)lists.netlojix.com > To unsubscribe send an email to jukebox-list-leave(a)lists.netlojix.com > %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s > Searchable Archives: http://jukebox.markmail.org/ > > > -- > This email has been checked for viruses by Avast antivirus software. > www.avast.com

1 0

Archives
by JIM & LAURIE DIRKSEN 08 Oct '23

08 Oct '23

I can't seem to find the searchable archives from the list. The link at the bottom of postings doesn't work. It could be operator error, but I like to think it's not. Maybe my phone settings? Anyone else have this problem? Thanks, Jim

4 4

Rock-Ola CD8C error message question.
by ron jukebox 06 Oct '23

06 Oct '23

Hello all. I have a Rockola Bubbler CD8C and when it is turned on, it give a ERROR message in the display. it says DIAGNOSTICS MODE CD Comm. Failure. Where do I start? Does anyone think it is possible that the board inside the CD PRO Player went bad? Hoping for some experienced folks to point me in the right direction. Thanks,Ron B

3 9

MRA1-L6 continued.
by Jukebox Repairman 03 Oct '23

03 Oct '23

This amp will play for about 2-3 minutes then blows the 2 amp fuse. Tubes all test good. I’m confused.

3 3

ROCKOLA MODEL 496
by Ron Medlin 02 Oct '23

02 Oct '23

Hi All, I have Rockola Model 496 with the System 3 Control Unit 55130-A with an intermittent problem. After power up, the machine will generally play a single selection correctly as per request. Generally, after playing the initial selection, it will not accept further selections. After power off, and several minutes wait time, it will repeat the same process. On one occasion, the machine attempted to play all selections in the carousel, after pushing several numbers on the keypad. I suspect a problem with the System 3 Control Unit, but I don't know where to start. Any tips? Ron Medlin 11815 E. 58th St. Kansas City, MO 64133 Home (816) 326-7399 Mobile (816) 419-7000

2 1

STD-4 Trip Problem
by Jim McClave 02 Oct '23

02 Oct '23

Mechanism trips continually as soon as a record is placed on the turntable. I read a short to ground across the trip switch on the mechanism continually. Disconnected the 6-pin plug on the amplifier and short still exists. Looks like the short is somewhere in the mechanism. Any ideas?

4 5

Seeburg STD 4 Trip Relay
by Jim McClave 01 Oct '23

01 Oct '23

Does anyone recall how many ohms resistance the trip relay coil should read? It is the little red "cube" type relay. Installed in the dcc4 control center. Im reading about 700 Ohms. Jim

1 0

Ok this one is odd
by Jukebox Repairman 01 Oct '23

01 Oct '23

Seeburg AY100, record is in play and when you make any additional selection it causes the mech to trip to scan ?? I’ve never encountered this before. Any ideas?

3 4

New Amp issue. Seeburg MRA1-L6
by Jukebox Repairman 30 Sep '23

30 Sep '23

This amp had been recapped awhile back and working properly. Owner said he went to play, powered on and a very loud hum then blew the fuse. He replaced with same value and same thing happened. Should I be looking for a shorted tube, open resistor?

2 2

Rowe CD 100 transfer motor
by Paul Howlett 28 Sep '23

28 Sep '23

I have a customer that has a CD100 that the transfer motor runs continuously. I have replaced the mech control computer (6108602) and tested the cam switches. If I stop the motor manually at a selected CD it will play the CD. The optical switches are working. The scan/transfer LED is constantly on. The board error LED is on intermittantly. -- Paul Howlett Pinball Paul's 703-361-0420

3 6

Seeburg MRA1-L6 AMP question
by Jukebox Repairman 28 Sep '23

28 Sep '23

I just finished installing a replacement cap kit in the above-mentioned amp. It is being used in a M100C. Using a redhead cartridge (with good needles) I'm finding the output of the amp is poor. Even with the volume maxed the output is nominal. I tested the tubes and the 6V6 drivers only read in the 50 percent range. A couple were 51 -52 but still low. Do you think a fresh set of tubes will increase the output? Regards, Rick

4 5

Seeburg V200 Does not pick up B sides (right side) records
by M De Simone 20 Sep '23

20 Sep '23

Hey All, A jukebox hobby friend asked for my help as he really doesn’t have computer savvy. He has a V200 with a TSR1 selection receiver. When he performs the battery trick all selections are selected and played. Making a selection from the keyboard works fine for all A (left side) selections but the mech will scan twice and not pick up any B side (right side) selections? He has tried swapping the 2D21 tubes and has traced out and verified all the wiring is good with continuity. To me it sounded like a readout problem at first but the fact that it selects and plays all selections when charged by a battery kinda eliminates a readout or trip.problem and the fact that it selects and plays A sides, I think, rules out a write in problem? I was hoping someone could offer some suggestions as I’m really not good at remote troubleshooting and this seems like a very odd problem to me. Much appreciated, Mauro Sent from my iPhone

4 6

NSM Prestige 2 IC 12
by Tony Miklos 18 Sep '23

18 Sep '23

On an NSM Prestige 2 on the board is an IC 12. It's an ER-1400. I think it's a ROM. I found some but do they need to be programmed? Thanks, Tony

1 0

78rpm reproduction records for sale
by joeymcd 12 Sep '23

12 Sep '23

Hey everyone. I have 8 used REPRODUCTION 78rpm records for sale. These would have been from the sets that were sold by Victory Glass and others. I took pictures and there is a list in with the pictures. Anyone interested can email me directly for the pictures and details. Postage by Canada Post. Joey McDonald

2 1

Seeburg R tonearm / trip issue
by Jukebox Repairman 11 Sep '23

11 Sep '23

I’m working on a R that just came in. As the tonearm enters into the cutoff portion of the record, instead of tripping off the tonearm jumps back into the record and then repeats this process and eventually will trip. There is a good loop in the tonearm wire so no bind there. Previous owner had installed an adapter to use stereo cartridge but I don’t think there’s any issue there. Could the tonearm balance weight cause this?

6 5

Seeburg Needle set-down
by Jim McClave 10 Sep '23

10 Sep '23

Is there a seperate needle set-down position on the seeburg mechanism ? SS-160 jukebox. The needle just barely misses the lead-in area and needs to be slightly adjusted. Thank yoiu.

3 2

Seeburg R tonearm / trip switch additional info
by Jukebox Repairman 08 Sep '23

08 Sep '23

Owner just provided additional info. He states that the tonearm also jumps into the record sometimes.

1 0

Seeburg MRA1-L6 Audio Question
by Jukebox Repairman 30 Aug '23

30 Aug '23

I recently completed cap replacement on the above mentioned amp. Bass response is poor and no change noticeable when changing the bass pot. The only thing I did different was on the .5 cap I used same value but a higher voltage. I can’t let it go sounding like this Thoughts? Regards Rick

3 3

Long haul shipper
by Rich Myers 29 Aug '23

29 Aug '23

I have a guy interested in shipping a W2700 up to MN. I haven't shipped before and wondered if anyone has a POC for a full service blanket/wrap shipper with good results. Appreciate on the help -rich myers Get Outlook for Android<https://aka.ms/AAb9ysg>

3 2

Rock-Ola 1452
by Jason Hall 29 Aug '23

29 Aug '23

Hey. I have a 50 selection 1452 and was wondering if I can use a 120 selection WALLBOX with it. Jason

2 2

Two questions related to the need to recap
by Paul Humel 24 Aug '23

24 Aug '23

I have two questions related to the need to recap. I am going to buy a W1-L56 Wallbox to use with my Seeburg Trashcan. I'm mainly concerned about the possibility of damaging the "unobtainium" transformer due to a failed capacitor(s). I'm also concerned about my Trashcan's Master Selection Receiver because I will be plugging in all the tubes back in that are needed for the "Wireless Wallbox" section of the Receiver. My philosophies are "If it's not broken, don't try to fix it", and "If you play with something long enough you will surely break it". So, to minimize "playing with it", can I simply rely on the fuses (I'm going to add one to the Wallbox) to provide protection against damage should a capacitor(s) fail? If a fuse blows, I'll recap. Or should I just bite the bullet now and recap both the Wireless Wallbox and the Master Selection Receiver? To my knowledge the Receiver has never been recapped. It has run fine for me since I bought it in 2018 and I removed all the tubes needed for the "Wireless Wallbox" section of the Receiver. Any thoughts, please. Thanks, Paul Humel

5 6

Seeburg STD 4
by Jim McClave 22 Aug '23

22 Aug '23

Can anyone tell me the correct name of this part Im looking for? Dont have the book for reference. It is a plastic block that rides under the tormat memory unit with two metal feeler contacts on it that make contact with the memory unit for selections. I have one metal contact broken off . Also, anyone direct me to someone who might have this ? thanks .

4 3

NSM Performer Grand CD Juke
by Jukebox Repairman 18 Aug '23

18 Aug '23

First time ever having one of these NSM machines in my shop. amplifier is only outputting right channel.. Does anyone have any info on transistor cross reference from one of the us suppliers like mouser or Newark, NTE? I searched the NSM part numbers from the manual and came up empty. Regards, Rick

3 2

2025

2024

2023