Hi Thomas, I disconnected the display and no change, as soon as I move the service switch from off to Service position power is applied to the mag motor. If I manually operate the detent coil the magazine starts spinning. This time additionally the CCC Display showed 9701 I've never seen that before???
On Wed, Sep 11, 2024 at 2:13 PM Thomas Teeter via Jukebox-list < jukebox-list@lists.netlojix.com> wrote:
Does it behave any differently with the display disconnected?
Thomas
On Wed, Sep 11, 2024 at 12:35 PM Jukebox Repairman via Jukebox-list < jukebox-list@lists.netlojix.com> wrote:
Karl, thanks did that already too Im baffled
Rick
On Wed, Sep 11, 2024 at 12:28 PM karl hjort via Jukebox-list < jukebox-list@lists.netlojix.com> wrote:
Does it have a DBA and controller? If so, disconnect the power to the controller, even if no DBA is present. That controller has had me
running
in circles before.
Karl Columbus Coin-Op Shop (Now retired but still piddling In Lehigh Acres, FL) ________________________________ From: Jukebox Repairman via Jukebox-list <
jukebox-list@lists.netlojix.com>
Sent: Wednesday, September 11, 2024 10:35 AM To: Jukebox mailing list jukebox-list@lists.netlojix.com Cc: Jukebox Repairman jukin510@gmail.com Subject: [Jukebox-list] Rowe R89 Strange Behavior
This is going to be a bit lengthy so bear with me.
I was called to a customer home for his juke not working after his home sustained a lightning hit. I was told that a TV, Pool pump, Dishwasher
all
damaged. His juke was not powered on during the strike but shortly
after
he
noticed it would not accept a selection.
In the display it would show first digit then when pushing 2nd digit
button
the display would go blank.
In service mode mech magazine would not rotate but you could hear a
click
from the sprag solenoid.
I replaced the mech controller board and no change. Next the Central computer still no change. I pulled his mech, Central computer, and
power
supply brought them back to my shop and tested each component one at a
time
in my shop machine and ALL his components work fine.
He brought the complete machine to my shop for further
troubleshooting. I
reinstalled all his original components and now in idle state the
magazine
motor is constantly receiving power pulses. If I manually operate the
sprag
assembly the magazine starts to rotate in a slow jerky motion. I even replaced the service switch but I am now at a loss what is
causing
this issue. Again all his original components operate properly in my shop machine.
I would welcome any input on what could be causing this.
Regards,
Rick _______________________________________________ Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/ _______________________________________________ Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/
Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/
Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/