Tony, i'll try that now Standby
On Wed, Sep 11, 2024 at 3:02 PM Tony Miklos via Jukebox-list < jukebox-list@lists.netlojix.com> wrote:
Did you try disconnecting the wires going into the Decibel display lights. That is if this is the same model I'm seeing. It has lights across the front that move with the music. I don't know anymore if that control board connects to only the amp, or if it connects to the CCC also.
On 9/11/2024 1:33 PM, Jukebox Repairman via Jukebox-list wrote:
Tony, I already did swap power supplies. I suspected the CCC may not be getting proper voltage but that was not the case
This really is a confusing one
Regards, Rick
On Wed, Sep 11, 2024 at 12:09 PM Tony Miklos via Jukebox-list < jukebox-list@lists.netlojix.com> wrote:
I don't know if it's tied to the CCC or just the amp, but try disconnecting the music decibel light display board. I'm assuming the voltages are good, but don't just go by the LED's. The CCC can have a lot less than 8vdc yet still light the led. Either way, try swapping power supplies.
Tony
On 9/11/2024 10:35 AM, Jukebox Repairman via Jukebox-list wrote:
This is going to be a bit lengthy so bear with me.
I was called to a customer home for his juke not working after his home sustained a lightning hit. I was told that a TV, Pool pump, Dishwasher
all
damaged. His juke was not powered on during the strike but shortly
after
he
noticed it would not accept a selection.
In the display it would show first digit then when pushing 2nd digit
button
the display would go blank.
In service mode mech magazine would not rotate but you could hear a
click
from the sprag solenoid.
I replaced the mech controller board and no change. Next the Central computer still no change. I pulled his mech, Central computer, and
power
supply brought them back to my shop and tested each component one at a
time
in my shop machine and ALL his components work fine.
He brought the complete machine to my shop for further
troubleshooting. I
reinstalled all his original components and now in idle state the
magazine
motor is constantly receiving power pulses. If I manually operate the
sprag
assembly the magazine starts to rotate in a slow jerky motion. I even replaced the service switch but I am now at a loss what is
causing
this issue. Again all his original components operate properly in my shop machine.
I would welcome any input on what could be causing this.
Regards,
Rick _______________________________________________ Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/
Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/
Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/
Jukebox-list mailing list -- jukebox-list@lists.netlojix.com To unsubscribe send an email to jukebox-list-leave@lists.netlojix.com %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s Searchable Archives: http://jukebox.markmail.org/