May 2024 - Jukebox-list - lists.netlojix.com

Rowe R-81 Memory Unit
by Tony Miklos 19 May '24

19 May '24

Is there any hope for finding a known good replacement memory unit #601-07666? I don't recall the condition of the bad board, last I saw it was 10? years ago and I couldn't find a replacement then.

3 4

Wurlitzer 1800 Pilaster Insert
by Tony Miklos 15 May '24

15 May '24

Is anyone reproducing the color and pattern insert for the wurlitzer 1800? I know Victory Glass has the glass, but they don't have the inner insert thingy. Thanks, Tony

3 7

Seeburg Q Stereo Crossover network & speakers needed
by Tony Miklos 14 May '24

14 May '24

Someone decided to make this Q better than factory and installed two new speakers, disconnected the mid-range speaker, and removed the crossover network. I'm not so sure if I need the speakers, but the crossover network would be very nice to have. Come to think of it, I'll have to test the mid/high range speaker.

2 1

SHFA1, 2, 4.. Mute/Squelch plug 5 pin
by Tony Miklos 12 May '24

12 May '24

Anyone have a mute/squelch 5 pin plug for sale? I may have a plug you need for trade. Tony

2 2

Help with Seeburg KD200
by morganfield1913＠gmail.com 07 May '24

07 May '24

Hello, I have a Seeburg KD200 which I have enjoyed for many years - recently the mechanism travels back and forth continuously and the keyboard is not active, ie. No sound of relays when a selection is made. I checked the voltage at the Tormat Electronic Unit (Type TEU-1) to be OK at -300V. The fault may be around the 'Write-In' circuits but I need some help in the diagnosis. I have a service manual. I will appreciate any suggestions. Regards Rod George Australia.

3 4

Seeburg M100A Buzzing
by Jim McClave 05 May '24

05 May '24

Problem still exists , buzzing starts as soon as machine is turned on. Not coming from the speaker, as Ive un-plugged the speaker. Its coming from the mech. Stuck in play position. When I peer thru the back with a bright light I can see the clutch stuck in the upward position. Is there any way I can un-stick it with a long screwdriver , etc? I know it will need taken apart and thouroghly cleaned and re-lubed. But is there any way I can get it un-stuck? Thanks.

2 1

AMI Conti2 record changer motor gear
by Federico Croci 05 May '24

05 May '24

Hello everyone! I have a problem with the gripper gear of my Conti2, not the one on the motor, the other one installed on the central mech. Actually, the hexagonal screw which keep the gear in its place got stripped, so I need to change it. The screw is the hexagonal one which keep in place the F2136 gear. Here is a picture of the gear itself: https://www.tilt.it/f2136_gear.jpg Mine jukebox is a Microtecnica italian Conti2, but usually parts are the same as other Continentals. Being in imperial size, not decimal, it's not an easy part to be found around here; actually, I do not even know what to look for, its real size! If you know its size, if you have that screw, if you have the full gear complete with the screw, I'd be interested in buying it; I'm sure the screw got stripped, not sure if the hole in the gear itself it's still ok. Thanks! -- Federico Croci wiz(a)tilt.it www.tilt.it

2 1

Joining the club with a Seeburg SMC2 Phoenix
by Kevin Moore 05 May '24

05 May '24

Hello All, I mostly or used to read and reply etc on the vector lists. But I have recently come across an SMC2 Phoenix Jukebox, that I'm trying to revive from the Dead. So far it appears that the Phono Control center is putting out decent voltages, but I will go through it soon. I have not touched the AMP as of yet, and have it unplugged. Working on the MCU1 module, batteries leaked because why not. Not to much damage. It did get some of the board interconnects and cables. I've got the MCU on the bench, providing 3.5vac and 40v to the display board along with 40v, 20v, +5 and +12 to the cpu board. The microprocessor, I'm not familiar with, but it does not seem to want to start running, until I give a bit of help. Then it starts to run. I get what appear to be random numbers and letters on the display. So at least I know the display works. Since I have no idea what information I should be seeing on the display I'm in a bit of a holding pattern. Thoughts on this endeavor, I'm not opposed to getting a Gen 2 cpu/display board, but would like to learn a but about this, and see if I could get it running. Kevin

2 4

Ami Continental 2
by john sharpley 03 May '24

03 May '24

Hi can any one help me. The rubber band from scan control box I have a new band, please can anyone assist me in the best way to fit it. Thanks in advance. John. Sent from my iPhone 14 Pro Max

1 0

tips for mounting main fiber gear Wurlitzer 61 anyone?
by Hans Minderman 02 May '24

02 May '24

Does anyone have any tips for mounting a new fiber gear on the main axle of a wurlitzer 61? The new replacement gears which are available through Victory Glass will be a tight fit and judging from the old (worn) gear that I just removed these things look to be brittle. Can these fiber gears be heated to let them expand a bit for an easier fit? Also, I saved the 3 copper rivets for the old gear, should I use those to fasten the gear once it is seated properly on the axle or are there other alternatives? Any tips from those of you have have gone over this procedure before are much appreciated! -Hans

3 7

2024

2023

Jukebox-list May 2024

2024

2023

Jukebox-list May 2024 ----- 2024 ----- May 2024 April 2024 March 2024 February 2024 January 2024 ----- 2023 ----- December 2023 November 2023 October 2023 September 2023 August 2023 July 2023 June 2023 May 2023 April 2023 March 2023 February 2023 January 2023

Jukebox-list May 2024