Autonomous vessel
by Bill Talanian
Autonomous vessel under development to use AIS as one tool in ships
identification. SBARC supports and maintains two AIS systems that cover
the south coastal region. The two systems nominally pick up vessels from
300 to 900 nm out to sea.
http://spectrum.ieee.org/automaton/robotics/military-robots/darpa-actuv-sel…
6 years, 11 months
- 1
- 0
QST
by Bill Talanian
QST
Effective this date the former GE Mstr II repeater and its associated
ACC RC-850 at the La Vigia site has been decommissioned. In its place is
a GE MSTR III which will act as a surrogate system without any bells and
whistles. It has the required time out timer and a CW ID. The remote TZ
receiver at UCSB and voter will go away for the time being. All voice
announcements has now gone away so personnel must make voice
announcements as needed. The wide-band GE MSTR III will remain in place
as a excellent standby system for the foreseeable future after system
upgrade.
As explained by Matt Lechliter, w6kgb, at last months club meeting, the
Mstr II will be converted to a uMstr with the addition of a new RLC Club
Controller. Essentially the former repeater retains the same electronic
design configuration. However, all the mixed cabling used for multiple
variants will be discarded which will make the system easier to maintain
by improving the common interconnections. A single RLC controller is now
capable of handling six serial interfaced independent systems, multiple
macros, and planned system interfaces tailored to the needs of
emergency services and daily users. Commonality of a single controller
will have the capability to interface the six-meter repeater, 440 IRLP
repeater, the UCSB remote link and voter, ELT receiver, NWS warning
system, etc. Command integration of the 146.79 and 145.18 repeaters will
now be possible via ethernet controls over the clubs microwave system.
Most importantly the controller will be ethernet capable which will ease
the load on control operators through remote configuration. We shall try
to maintain the basic configuration of the previous club and ARES net
functions as best possible. But no two systems have the same design
features and capabilities so we must adjust and learn. As we move
forward the first task is to upgrade the MSTR II to a uMstr. This should
take about 2 months. Meanwhile the task of interfacing the six-meter and
440 system will be on-going. In time you shall see a much more capable
system.
A last word about the RC-850. The controller was way ahead of its time
in the 70's. It has served the club extremely well by performing a
myriad of timed macro's, voice synthesizer, paging variants, auto-patch
capabilities, plus many control bells and whistles as a single system
controller. The limitation of the 850 was interfacing of remotes or
additional functions plus finding personnel who wanted to spend their
time understanding the unique command software controls and becoming a
good control operator-engineer. Hat's-off to the ACC people. They
designed a controller that worked flawlessly for over 35 years. But time
moves on. Hopefully the new system will attract competent technical
people who love to work with systems integration.
Bill Talanian
6 years, 11 months
- 1
- 0
SBARC April EmComm and ATVSIG Reports
by Rod Fritz (rod＠sbatv.org)
Hello SBARC Members and Friends,
Many of you have shown interest in Emergency Communications (EmComm) so I wanted to send you this report that I just sent to the SBARC Board.
I encourage you to participate actively in EmComm. It may well be the most important thing we can do as radio amateurs.
Some of you may not know that I moved to Mesa AZ about 2 years ago when I retired. I've tried to remain as active as possible in Santa Barbara and have visited often. I've finally discovered that I'm not very effective in a leadership role unless I can physically be there more than is currently practical. I'll continue to be as active in SB as I can.
After living in Santa Barbara for 35 years, I have deep roots and consider it home. I hope to move back as soon as I can (though I'll retain my nice home in Mesa) and I want to continue to contribute to the SB community.
I also included my Amateur Television report so you can be aware of what's going on.
Feel free to send questions and comments to me at rod(a)sbatv.org.
Regards,Rod Fritz, WB9KMO
-------- Original message --------
From: "Rod Fritz (rod(a)sbatv.org)" <rfritz22(a)cox.net>
Date: 4/13/2016 2:18 AM (GMT-07:00)
To: 'Dorothy Oksner' <oksner66(a)gmail.com>, bodall(a)sbarc.org, 'Dorothy Oksner' <ox(a)silcom.com>, 'Darryl Widman KF6DI' <kf6di(a)sbarc.org>, 'Rick Whitaker' <rickwhtr(a)cox.net>, 'Bob Muller' <rmuller65(a)gmail.com>, rod(a)sbatv.org
Subject: SBARC April EmComm and ATVSIG Reports
Rod
Fritz, WB9KMO
EmComm Committee - Brian
and I co-chair this committee
As a practical matter, I find it in SBARC's and in my
best interest to resign as co-chair of the EmComm Committee, leaving it solely
in Brian's capable hands until he appoints another co-chair. I hereby resign
with these parting recommendations...
Purpose: Successfully complete
these three EmComm projects to
substantially help provide services to the community in times of
need...
. INFRASTRUCTURE - Implement and
maintain repeaters, radios and a mesh network and train hams and others in the commmunity to use
them effectively
. GROUP COMMUNICATION SUPPORT
- Work with existing groups like HOAs, retirement homes and mobile home parks to
integrate communications into their emergency plans
. CITIZEN COMMUNICATION SUPPORT
- Work with all citizens, households, neighborhoods and service providers
to fill communication gaps to provide
services when 911 can't
INFRASTRUCTURE - Maintain and evolve the
infrastructure we have and continue to build and use a mesh
network for EmComm and other constructive
uses.
GROUP COMMUNICATION
SUPPORT - Continue working
with group communications to define what needs to be done and establish and test standards that will
benefit everyone.
CITIZEN COMMUNICATION
SUPPORT - The prime objective is to answer the question, "Who ya gonna
call if 911 doesn't work?" Identify
and fill a set of communication gaps to effectively
serve the community at large with emergency communications. This need extends beyond Group Communication Support to
provide a plan, a structure and a method for all people in the community to gain
access to services (not just communicate) when 911 falls
short. This
solution needs to serve at the individual/household/family level (not just associations). Households can contact
neighborhood reps and other
communicators to ultimately reach radio amateurs who can fill the
communication gaps. This communication needs to
be end-to-end and back (two-way closed loop) to ensure that the service
providers are reached and so the people in need know that help is on the
way.
An EmComm meeting we held last year helps us understand what this is
about, how it might work and the types of things we need to
do. These are the key conclusions
from a paper exercise to save
someone trapped in a building when 911 couldn't be reached...
. During the first 72 hours of a major emergency, 911 will likely not be
able to meet everyone's needs
. Resources will focus on what they can do to benefit the most important
locations and largest groups of people
. If 911 doesn't work, the EOC is NOT the place to contact to get
services
. Resources may be available, but may be difficult to
contact
. If 911 and other direct communication to services don't work, citizens
likely don't know who else to call or how to call
them
. It makes sense for radio amateurs and others in the community to model
who can do what and to document alternate ways to contact
them
. In our exercise, it was easy to identify communication gaps that radio
amateurs can help fill, but we only scratched the
surface
. Lessons learned and potential objectives discussed
were...
.. All service groups
need to identify the scope of what they can and cannot do and alternate ways to
reach them
.. Generally, service
groups provide great services but are weak on
communication
.. Radio amateurs can
provide excellent communication, but they cannot provide other
services
.. Prepare citizens to
contact radio amateurs using all available communication resources, including
person to person
.. Prepare radio
amateurs to communicate with other communication groups and service resources
that citizens need
.. Establish redundant
ways to communicate so if the primary fails, at least one alternate is in
place
.. Try to ensure that
communication is acknowledged from the citizen to service resources and back to
the citizen to minimize confusion and be most
effective
.. Establish and
document processes to make end to end communication most
effective
.. Make citizens aware
of what they, we and other resources can do
.. Train everyone
involved and carry out regular exercises to ensure the processes work and to
optimize them
.. EmComm participants can keep in
touch by email until another in-person meeting is justified (Email
isn't working well. It is time for an
in-person meeting.)
This is admittedly a huge undertaking, but the
need is critical. Without us to fill the communication gaps (nobody else
is), the consequences will be devastating to thousands of people in the
community during a major disaster. This is the magnitude of a challenge
that will make the community stand up and notice that we can provide
life-improving coordination and communication service to the community. I
guarantee that we would no longer be considered a club of ineffective
introverts. We are uniquely capable of mobilizing the community and
integrating it's support organizations to do what needs to be done. There
are too many communication gaps for community support to be effective without us
stepping in.
Consider this... If we don't do something like this
that is so valuable that the whole community stands up and notices, we are
doomed to a fate of uselessness. This kind of community support is a key part of
our mission.
I will do what I can to help, but unfortunately, no
longer as the commitee co-chair. Please promote this cause and make it
happen.
Rod Fritz, WB9KMO
EmComm Committee Co-Chair,
Resigned
ATV
Special Interest Group (ATVSIG) –
Chaired by Rod Fritz
Purpose: Develop a plan and implement it to promote amateur television
and other amateur radio specialized modes.
I and many others are making good
progress implementing mesh networks in Santa Barbara, Mesa AZ and
other parts of the country. I'm trying to develop a practical way to run a
video net on the mesh. I'm also testing a method to integrate analog and digital
video over the Internet and/or mesh networks using Grandstream GXV3500
devices. If any of you are interested in participating in these projects, let me
know.
I'm continuing to make progress
testing 2 MHz-wide
DVB-T digital ATV on 434 MHz. It provides excellent quality standard-definition digital video at very low signal levels, allowing it to be used over
long distances and when a line of sight communication path is not
available. Some of you who can't get
into the ATV repeater now may be able to get in with DVB-T. I expect to install a DVB-T receiver on the ATV
repeater in Mesa AZ in the next month and then in Santa Barbara shortly after
that. Reception of these signals from the repeaters will not change now, but
plans are in place to transmit high-definition DVB-T as well as analog ATV on
the repeater outputs in the near future. Keep in mind that I will
also soon enable mesh video on the ATV repeaters and will be capable of
putting ATV video on the mesh. Again, let me know if you're interested in
participating.
ATV is at
the SBARC Club Station and is being
maintained and upgraded on an ongoing basis. Let me know if something needs attention. We've
operated out of the Rover on numerous occasions and it's relatively easy to set
up. I'm looking for one or more local
champions to learn how to use the ATV and mesh video gear, teach others and use
it for fun and for events.
Steve Noll WA6EJO, who lives in Ventura, helps me care for the SB ATV repeater and ATV equipment at the Club
Station. He can be there in person when I'm
not in SB.
There are several other ATV
Stations in SB. Let's get them back on the
air. It just takes a little interesting activity. Soon, the Amateur Television
Network link will be improved. It's ready for installation in Oxnard. That will
allow access to dozens of other ATVers (and meshers) in CA, NV and
AZ.
There is an ATV Net on Tuesday nights
at 7:30pm, controlled in L.A. that can be accessed in SB. You can all watch
it on the Internet at www.batc.tv, ATV
Repeaters, W6ATN. Check it out sometime. When you master that, there
are several other U.S. and international ATV signals available on that site,
plus some videos that were recorded in the Santa Barbara area. Browse and
enjoy...
I look forward to seeing you on amateur
radio real soon!
Rod Fritz, WB9KMO
ATVSIG Committee
Chair
6 years, 11 months
- 1
- 0
Re: [Sbarc-list] Hello there
by Darryl Widman
Hi Dave,
How nice to hear from you.
I have an idea. How about putting your need on our Club’s list server! In fact, I think I will do that right now. Nothing ventured, nothing gained.
Hang on, I’ll do that right now. Let’s hope you hear from someone soon!
73, Darryl, KF6DI
BTW, Dave, probably by now most of our members don’t know you or of you and that you are a long-time member of SBARC. In fact, you were our Club Secretary for quite a while, were the chairman of the Hamfest Committee and did a fantastic job for us. In fact, folks, Dave is probably the neatest, tidiest, cleanest guy you have ever met and would leave your place far cleaner than he found it! You can send Dave, K6VML, a note at dhackleman(a)verizon.net.
From: David Hackleman
Sent: Monday, April 04, 2016 10:57 AM
To: auditron(a)juno.com
Subject: Hello there
Darryl,
I had an e-mail almost ready to send you but I accidentally erased it instead. It's too easy to do on the cheap little notebook computer I'm using. So I attached an external keyboard this time.
I was wondering if you knew of anyone who I might stay with when I make visits to Santa Barbara/Goleta. I would offer to organize their garage or a room in the house or do yardwork for the privilege. Harry and Carmen had offered to have me stay at their place but they are unable to now. Of course it is expensive to stay at a motel there and staying at a cheaper one down south in Carpinteria or Ventura is inconvenient. I talked to Harry on the air during last year's Route 66 On the Air event that our club heads up. He was glad to talk to me and very appreciative that I could leave Carmen a voicemail while he was out and about on Route 66. He was determined to do it this time and had to reassure Carmen that he would be responsible!
I start work at an Amazon warehouse in San Bernardino in a week or so. I had worked there as a temp for 3 months ending in mid-February. I was a "picker" so I pushed a cart around all 10 hours and got orders out of bins. I actually got pretty good at it and would like them to give me that job again on the warehouse floor. It is supposedly the elite position with the most pressure. As I say I liked it and I lost 17 pounds while doing it! This time I was hired directly by Amazon which means I will get benefits!
My dad is doing well for 94. My brother and I visit him daily which has kept me somewhat tied down here. Anyway it would be nice to drive up there sometime in the near future and see everyone. I don't know what my schedule is yet, last time I worked Friday thru Monday so I wasn't able to go to SBARC meetings during that time.
I hope all is well with you and Diana! Will talk again soon.
Dave K6VML
6 years, 11 months
- 1
- 0